Brick

From The iPhone Wiki
Revision as of 01:44, 1 June 2015 by Dayt0n (talk | contribs) (Intentionally modifying key parts of iOS: changing NVRAM variables to invalid values)
Jump to: navigation, search

A bricked device is a device that does not work. The direct metaphorical meaning is that the device is permanently damaged (making it as useless as a brick), but people use the term "bricked" for non-working conditions which range from easy to fix (such as a failed update) to impossible to fix (such as damaged baseband memory). A phone may be called "bricked" if it will not boot, will not respond to input, will not make calls, etc.

Difficulty of bricking an iOS device

Using a jailbreaking tool cannot put a device into an unusable state on its own - if something goes wrong while jailbreaking, putting the device into DFU Mode will allow you to restore it via iTunes. Installing software via Cydia also cannot cause an unrecoverable state (unless very specifically designed to do so by a malicious person, which has not been seen "in the wild"). Other than that specific exception, if something goes wrong, DFU mode will still work.

Types of "bricking" that can be easily fixed (not really "bricking")

Installing stock iOS on a device with a preserved baseband

Early unlock solutions could result in unusable (but recoverable) phones after installing an iOS update if you didn't take special steps. For people who used redsn0w to install the iPad baseband (06.15.00) on a compatible iPhone 3G or iPhone 3GS so that they could use ultrasn0w to carrier unlock it, upgrading or restoring iOS using "stock" (normal) IPSWs would make the phone unusable - until you made and restored a "custom" IPSW without a baseband update (instructions), and then reinstalled the iPad baseband using redsn0w. Avoiding doing a stock upgrade/restore (upgrading or restoring iOS using a "custom" IPSW) avoided this problem.

Intentionally modifying key parts of iOS: changing NVRAM variables to invalid values

In February 2015, researchers released information about how to change an nvram variable called DClr_override. If this is changed to an invalid value for the device (valid values are not the same on all devices), and the device is rebooted, the device will not be able to boot. iOS 8.3 beta 4 (released in March 2015) removes the DClr_override variable, and later iOS versions will probably omit it as well. This means that restoring a device to iOS 8.3 beta 4 (or later) will fix the device, rendering it bootable once again.

Types of bricking that may be hard to fix

Changing MAC address to invalid address

If you change your device's MAC address to something invalid (for example if you're attempting to change your UDID), your internet won't work again until you fix the MAC address (using MobileTerminal or similar). This persists even if you restore -- so you can make this really really hard to fix if you restore and there's no jailbreak available, if the available jailbreaks don't include afc2 and other workarounds aren't working, etc. Here's a JailbreakQA thread about this and another one.

Intentionally modifying key parts of iOS: other ways

If you purposefully erase / zero out your NOR, then you will have trouble doing a DFU restore because important information from the SysCfg section will not be available.

See winocm's explanation of several related ways to brick a device:

  • Erase SysCfg/replace it with 0xFFs.
  • Destroy the 'SrNm' tag in the SysCfg, it won't activate then.
  • Set all clock gates enabled and set PLL frequencies to mad numbers, THIS WILL DAMAGE THE HARDWARE.
  • Run constant NAND stress tests to wear out NAND pages.
  • Set the 'display-timing' nvram variable to some other garbage. iPod touch 2G/3G does weird things with that.

If you know how the hardware works, this can be done from an iBoot/kernel level.

Making the wrong modifications to the baseband

One way to irreversibly brick a device in software is to flash an invalid baseband bootloader, provided it has a baseband. Most other bad flash scenarios are recoverable some way or another.

Another way to brick the baseband is by installing baseband 06.15.00 on an incompatible device. redsn0w has an option to install this baseband on the iPhone 3G or iPhone 3GS in order to get a baseband version that is unlockable with ultrasn0w. This is a nice way to get an unlock, because the iPad, the iPhone 3G and the iPhone 3GS all share the same Baseband Device, but the iPad has a newer version number in its baseband. That way people can actually downgrade by installing a higher version (there are no APTicket checks in these devices). This has known side-effects, like losing GPS functionality (this baseband comes from an iPad which has no GPS or differently implemented).

It was possible to brick an iPhone 3GS with this method. In fall 2011 Apple replaced the NOR flash. It is not clear if this was done intentionally to prevent this method. The previous type of baseband was 36my1ee and they changed it to 36my1eh, 36my1eg. (There was no switch to Toshiba baseband devices.) These new NOR flash chips seem to work with the newer baseband versions in the iPhone 3GS, but are not supported with the old 06.15.00 baseband. Therefore installing this version will brick your device if you have a new NOR flash, as you (currently) cannot go back and install anything else. To check before installation, check the version number, as it reveals the production year/week in the digits 3...5. Week 34/2011 appears safe, 35 seems iffy, 36 seems iffy, 37 is not safe. Or open the device and check the chip type.